Home > Products > Intelligent Control > Temperature Controller

Duct Temperature Sensors 0-10V

FOB Price:

US 22-28 / Piece

Min.Order Quantity:

50 Piece/Pieces

Supply Ability:

500 Piece/Pieces per Month

Port:

Shanghai

Place of Origin:

Shanghai, China (Mainland)

Payment Terms:

L/C,T/T,Western Union,MoneyGram

Brand:

CH-BA

Products Model:

T-U-D-10

Products Details
Company Profile

Quick Details

Brand Name: CH-BA

Model Number: T-U-D-10

Place of Origin: Shanghai, China (Mainland)

Packaging & Delivery

Packaging Details: carton
Delivery Detail: Shipped in 3 days after payment

Specifications

Air Duct Temperate Sensor Features

· Thermistor,PT or NI sensing elements to fit your system

· Simple and secure installation

· Wide range of temperature probes

· Compact size and modern design

Applications

· On return air ducts to measure heating/cooling return air

· On supply air ducts to measure heating/cooling supply air

· In heat exchangers and air handling units to control heating/cooling coils for temperature and humidity control

· As frost protection sensor

Temperature Sensor

The sensor measures the temperature by use of a NTC, PT or NI sensing element. The sensing element is either a glass packed thermistor with a negative temperature coefficient or a platinum film sensor or a thin nickel layer on a ceramic substrate. Its resistance changes according to the temperature. The change follows a specified curve. Below is a list of available sensor elements, curves and accuracies:

Item name	Sensing element	Curve	Compatible with
N18	Thermistor 1.8k at 25 °C	Curve 5	TAC, CSI
N3	Thermistor 3k at 25 °C	Curve 6	Alerton
N10	Thermistor 10k at 25 °C	Curve 24	Hysine, Alerton,ALC, Delta,Trane, CSI
N11	Thermistor 10k at 25 °C	Curve 7	Andover, Invensys, Carrier, KMC
N20	Thermistor 20k at 25 °C	Curve 20	Honeywell
N100	Thermistor 100k at 25 °C	Curve 9	Siemens SBT
Tp1	PT100	0.3851ohm/K	Honeywell
Tp2	PT1000	3.851ohm/K	Johnson Control
TK5	NI1000	5000ppm/k	Siemens SBT

Ordering

Ordering number:TS-XX-D-YY

XX indicates the sensor element optional,see table above.

YY indicates the probe length. Standard probe length is 20 cm.

For example:TS-N10-D-20

-N10 indicates the sensor element is Thermistor 10k .

-20 indicates the probe length is 20 cm.

Duct probes should be installed directly on the duct, in an area where the air stream is well mixed:

· Locate a supply air sensor two or three meters down stream from the nearest fan and coil.

· Mount the return air sensor close to the air inlet but downstream from a return fan if one is present.

· To install the sensor, assemble base plate and probe, then drill a 8 mm hole and two 3 mm holes on a diameter of 25 mm in the duct.

· Use two self-tapping sheet metal screws to tighten the mounting circuit in the cover.

· Connect the wires according to the wiring diagram to the measuring circuit in the cover:

o The Thermistors require two conductors; normally 18ga unshielded twisted pair.

o The PT100, PT1000 and NI1000 sensors come with each two terminal connectors in order to connect up to four conductors for compensating conductor resistance.

· Assemble the cover with the mounting plate.

· Insert the assembled probe through the center opening of the mounting plate into the air stream.

· Tighten the horizontal screw on the mounting plate to fix the probe to the duct.

Technical Specification

Sensing Probe	Thermistor: Range Accuracy	NTC -30----70°C ±0.5k
	Platinum-Film: Range Accuracy	PT, 0.3851ohm/k -30----70°C ±0.3k
	Nickel Thin Layer Range Accuracy	NI, 5000 ppm/k -30----70°C ±1k
Connection	Connection Terminals	2.5 mm²
Environment	Operation Climatic Conditions Temperature Humidity	To IEC 721-3-3 class 3 K5 -4070°C <95% r.h.
Environment	Transport & Storage Climatic Conditions Temperature Humidity Mechanical Conditions	To IEC 721-3-2 and IEC 721-3-1 class 3 K3 and class 1 K3 -4080°C <95% r.h. class 2M2
Standards	conform according to EMC Standard 89/336/EEC EMEI Standard 73/23/EEC	EN 61 000-6-1/ EN 61 000-6-3
	Automatic electrical controls for household and similar use Special requirement on temperature dependent controls	EN 60 730 1 EN 60 730 2 - 9
	Pollution Class	Normal acc. To EN 60 730,RoHS compliant
	Degree of Protection	IP56 to EN 60 529
	Safety Class	III (IEC 60536)
Housing Materials	Cover & Mounting Plate Probe	Fire proof ABS plastic Stainless Steel
General	Dimensions [mm]	Cover: 42 x 112 x 88 (H x W x D) Probe: ø 6 x 200 (Diameter x L)
General	Weight (including package)	135g

Package and Shipping

Sample Order	Order	OEM Order
Three work days	2 weeks	3 weeks

Port

Shanghai

♦ Specilizng in manufacturing products of HVAC for almost 10 years.

♦ Harsh process of production and strict testing system.

♦ High quality with competitive price.

♦ Delivery in time.

♦ Reply in 24 hours.

Please feel free to contact the supplier if you need more information or help.

Email to this supplier
To :

Kitty Weng | Shanghai huikong Energy Source Co., Ltd
*Subject :
Quantity Order:
*Message :

Please enter your message.
Your message must be between 20-2000 characters

+ Add attachments :
Select File (Max 2 files)
Please enter your company name:

Please make sure your company name is entered correctly.
* Please enter your email address:

Please make sure your email address is entered correctly.
* Please enter your mobile phone:

(+) -

Please make sure your mobile phone is entered correctly.

Verified Supplier - Shanghai huikong Energy Source Co., Ltd Bussiness Type: Manufacturer
Scale: 11 - 50 People
Country/Region: China (Mainland)/Asia
Established: